 |
YOU KNOW YOUVE FOUND YOUR CARP FORUM HOME! |
Toasteds Advanced British Carp Forum
Welcome to toasteds.co.uk "THE ADVANCED BRITISH CARP FORUM"
The uk`s most chilled carp fishing forum:splicing leadcore the animated how2
USING AND SPLICING LEADCORE SAFELY.
LEADCORE SPLICE TO MONO/BRAID:leadcore is a woven type braid with a inner core or lead wire.The main use of leadcore is to pin the last few feet of line to the lake bed so the carp dont spook off it. when using leadcore you need to always check that your lead or swivel will slide over any knots tied especialy the knot joining the leadcore and the easiest way to do that is by splicing your mainline to the leadcore. 
step 1: pull out about 1-2 inches of the inner leadcore so one end hasnt got any lead inside for the last inch or two. step 2: slide your baiting needle or nut drill into the leadcore about 1-2 mm (the end without lead inside) step 3: now lightly burn the end of the leadcore minus the lead with a lighter so its a solid edge with a clean hole in the center. step 4: now as shown in the picture push your baiting needle into the leadcore where theres no lead about a inch or more from the end. step 5: now push the baiting needle through the inner core "about 1-2 inches" and out the end. step 6: hook your mainline onto the baiting needle. step 7: now pull the loop of main line inside the core and back out the side i normaly use a loop of amnesia to splice leadcore and find it easier than splicing leadcore with a baiting needle or proper leadcore splicing tool. use this knot to finish off the splice 
KNOT FOR JOINING TWO LINES:this knot can also be using for joining shockleaders to your mainline. you have to also tie the same knot on the other line,then moisten and pull together tight.
LEADCORE LOOPED SPLICE:this leadcore loop splice is generaly used for atatching to your swivel on your hooklength. step 1: pull out about 1-2 inches of lead from the core so one end hasnt got any lead for the last inch or two. step 2: slide your baiting needle or a drill bit end into the leadcore about 1-2 mm (the end without lead inside) step 3: now lightly burn the end with a lighter so its a solid edge with a clean hole in the center. step 4: now as shown in the picture push your baiting needle into the leadcore end and back out the side about a inch from the end. step 5: now hook the other end of the leadcore onto the baiting needle or loop of amnesia and pull back into and through the inner core. step 6: now pull it all the way through to form a loop. |
TOASTEDS ADVANCED BRITISH CARP FORUM
WRITERS AND ARTICLES WANTED: please email all original carp fishing articles to toasted@toasteds.co.uk ,original uk,french and worldwide venue reviews are also needed, please send these to the same mail address
Links and articles:
HOME.A-tract Baits For all your boilies and pellet mixes.
A-tract Baits Field testers catch reports.
Fishing Around the World: lake nasser nile perch by s.kibble
Bait: Beware of the Glug in Winter by s.kibble
British Carp Fishing: Fishing Wraysbury No1 by s.kibble
illegal imports When will they learn by s.kibble
Cat fishing fishing for wel`s catfish in spain by s.kibble
winter carping Cold water carping in holland
nickolls leisure park a review of the nickolls leisure park
The under estimated stretch.The quest for big river carp
The Northern Social @Selby 3 lakesThe lowdown on the 2005 northern social . (The long awaited write up).
knot tying made easy video`s,animated picures,step by step guides to tying knots
splicing leadcore a how too for splicing leadcore loops and splicing leadcore to mono/braid
frobury farm lakes run down on the frobury farm complex
Mescar-Lake mescar lakes coarse fishery write up
Toasteds carping basics Learn how to tie hair rigs, advanced carp rigs, setup a bolt rig, helicopter rig and particle preperation times.
Feature Finding With pictures and text to make it easy!
|
|
If you like this carp, cat, pike and coarse fishing forum, click the logo to vote for the best uk carp fishing forum. |
